Active-semi PAC5532EVK1 User Manual Download Page 14

14    -                                              Rev 1.0 February 2018 

A

BOUT 

A

CTIVE

-S

EMI 

® 

Founded in 2004 in Silicon Valley and headquartered in Allen, Texas, Active-Semi® is a rapidly 
emerging leader in the multi-billion dollar power management IC and intelligent digital motor drive IC 
markets. The company's portfolio of analog and mixed signal SoCs (systems-on-chips) are scalable core 
platforms used in charging, powering and embedded digital control systems for end applications such as 
industrial, commercial and consumer equipment. The company offers power application 
microcontrollers, DC/DC, AC/DC, PMU and LED drivers that significantly reduce solution size and cost 
while improving system-level reliability. Active-Semi's turnkey solutions deliver energy-saving power 
conversion architectures that minimize energy usage and compress system development cycle-time by 
greater than 50 percent. Active-Semi ships 50 million power ICs per quarter and reached the "one billion 
units shipped" milestone in May 2012. The multi-national company focuses on commercializing industry 
leading power management IC solution platforms and has developed broad intellectual property with 
over 150 patents granted and pending. For more information visit: 

http://active-semi.com/

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
LEGAL INFORMATION & DISCLAIMER 

 

Copyright © 2018 Active-Semi, Inc. All rights reserved. 
All information provided in this document is subject to legal disclaimers. 
Active-Semi reserves the right to modify its products, circuitry or product specifications without notice. Active-Semi products are not intended, designed, warranted 
or  authorized  for  use  as  critical  components  in  life-support,  life-critical  or  safety-critical  devices,  systems,  or  equipment,  nor  in  applications  where  failure  or 
malfunction of any Active-Semi product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Active-Semi 
accepts no liability for inclusion and/or use of its products in such equipment or applications. Active-Semi does not assume any liability arising out of the use of any 
product,  circuit,  or  any  information  described  in  this  document.  No  license,  express,  implied  or  otherwise,  is  granted  under  any  patents,  copyrights  or  other 
intellectual property rights of Active-Semi or others. Active-Semi assumes no liability for any infringement of the intellectual property rights or other rights of third 
parties  which  would  result  from  the  use  of  information  contained  herein.  Customers  should  evaluate  each  product  to  make  sure  that  it  is  suitable  for  their 
applications.  Customers  are  responsible  for  the  design,  testing,  and  operation  of  their  applications  and  products  using  Active-Semi  products.  Customers  should 
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. All products are sold subject to Active-
Semi's terms and conditions of sale supplied at the time of order acknowledgment. Exportation of any Active-Semi product may be subject to export control laws. 
Active-Semi®,  Power  Application  Controller®  and  PAC®  are  registered  trademarks  of  Active-Semi,  Inc.   Solutions  for  SustainabilityTM,  Micro  Application 
ControllerTM, Multi-Mode Power ManagerTM, Configurable Analog Front EndTM, and Application Specific Power DriversTM are trademarks of Active-Semi, Inc. 
ARM® and Cortex are registered trademarks of ARM Limited. All referenced brands and trademarks are the property of their respective owners. 
 

Summary of Contents for PAC5532EVK1















Reviews: