background image

Art. Nr.: 12200R Cabrio 

Page 16 of 22 

EN 

 

11.  Connecting the gas cylinder and checking for leaks 

The following parts are required to connect the device:  

  Commercially available camping gas bottle 5 - 11kg filling weight, e.g., gray camping 

propane gas bottle. You buy these from a liquid gas dealer. The empty cylinder is    
replaced for refilling. 

  Fixed, DVGW-approved pressure reducer, max. 1.5 kg/h, operating pressure 50 

mbar, suitable for the gas cylinder use, included in delivery. 

  DVGW-approved hose line of sufficient length (included in the scope of delivery) that 

allows kink-free installation. It is part of the device. A porous or damaged hose line 
must be replaced immediately. The hose line is already pre-assembled at the factory. 

  Leak detection agent, e.g., leak detection spray or soapy water. 

 

1.  Check the presence and proper condition of the cylinder valve thread seal, also at 

each cylinder change. Do not use any additional seals. 

2.  Connect the union nut of the pressure regulator to the cylinder valve thread by turning 

it counter clockwise by hand. Do not use any tools, as this may damage the cylinder 
valve seal and thus the tightness is no longer guaranteed. 

3.  The hose line must be connected firmly and tightly to the pressure regulator outlet 

thread by turning it to the left using an SW 17 spanner. 

4.  The connection of the other end of the hose line to the threaded connection piece of 

the unit is already pre-assembled. This connection must also always be very tight. Al-
ways check all connections carefully before using the appliance. 

5.  Check all connections for leaks under operating pressure using a leak detector. Leak 

tightness is ensured if no bubbles form.  

Checking for leaks with an open flame is not permitted. Leaky or damaged hoses and 
fittings must be replaced without exception 

6.  In the event of gas leaks, shut off the gas supply immediately and repair the leak or 

replace the defective part.  

7.  To replace the gas cylinder, proceed as follows: 

  Choose a place away from any source of fire. 

  Close the cylinder valve. 

  Loosen the union nut from the pressure reducer. 

  Remove the pressure reducer from the cylinder. 

  Fit the bottle valve with a protective cap. 

  Connect the new bottle as described from point 1. 

 

Cylinder valve screw with inserted seal 

Connection nut (Left hand thread!) 

Regulator output thread (Left-hand thread) 

Hose pipe 

Pressure 

regulator 

Cylinder valve 

Gas cylinder 

Union nut (Left-hand thread

Summary of Contents for 12200R Cabrio























Reviews: