background image

www.acti.com

USER’S MANUAL 

 

Regulatory Information 

FCC Information 

Please take attention that changes or modification not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the equipment. 

FCC compliance: This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:   

—Reorient or relocate the receiving antenna.   

—Increase the separation between the equipment and receiver.   

—Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.   

—Consult the dealer or an experienced radio/TV technician for help 

This equipment should be installed and operated with a minimum distance 20cm between the 

radiator and your body. 

FCC Conditions 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions:   

1. This device may not cause harmful interference.   

2. This device must accept any interference received, including interference that may cause 

undesired operation. 

Now that the camera and the PC are both having their unique IP addresses and are under the 

same network segment, it is possible to use the Web browser of the PC to access the camera. 

 

 

 

Summary of Contents for R71CF-38




















Reviews: