background image

www.acti.com

  Hardware Manual 

                 

Precautions 

Read these instructions 

You should read all the safety and operating instructions before using this product.   

 

Heed all warnings 

You must adhere to all the warnings on the product and in the instruction manual. Failure to follow 

the  safety  instructions  given  may  directly  endanger  people, cause  damage  to  the  system  or  to 

other equipment.   

 

Servicing   

Do not attempt to service this video device yourself as opening or removing covers may expose 

you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 

 

Trademarks 

All names used in this manual are probably registered trademarks of respective companies.   

 

Liability 

Every reasonable care has been taken during the writing of this manual. Please inform your local 

office  if  you  find  any  inaccuracies  or  omissions.  We  cannot  be  held  responsible  for  any 

typographical  or  technical  errors  and  reserve  the  right  to  make  changes  to  the  product  and 

manuals without prior notice.   

 

FCC/CE Regulation 

Note:

 This equipment has been tested and found to comply with the limits for a Class  A digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection  against  harmful  interference  when  the  equipment  is  operated  in  a  commercial 

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction manual, may cause harmful interference to 

radio communications. Operation of this equipment in a residential area is likely to cause harmful 

interference  in  which  case  the  users  will  be  required  to  correct  the  interference  at  their  own 

expense. 

 

 

Summary of Contents for KCM-3311
























Reviews: