background image

 

                    ACTinBlack Europe S.à r.l. Rev 1.0, May 2020 

9

 

2.4

 

Eyecup Installation: 

Perform the following procedure to install eyecup 
onto the Binocular. 

1.

 

Carefully  press  the  eyecup  over  the  end  of  the  eye  cup 
retainer  ring. 

Rotate  the  eyecup  into  proper  viewing 

position.  Adjust  for  best  fit.  The  eyecup  must  seal 
around  your  eye  and prevent  the  green  glow  from 
escaping. 

 

2.5

 

Demist Shield Installation: 

Perform the following procedures to install the demist 
shield on the eyepiece lens. 

1.

 

Carefully remove the eyecup. 

2.

 

Carefully remove the eye cup retainer ring by rotating 
it counter clockwise 

3.

 

Screw the demist shield assembly in clockwise 

4.

 

Screw the eye cup retainer ring into the demist shield 

5.

 

Carefully replace the eye cup on the eye cup retainer 
ring. 

 

CAUTION 

If the demist shield is wiped while wet or with wet 

lens tissue, you will damage the coating. 

 

NOTE 

If inclement operating conditions are expected to exist 

(e.g. significant temperature change and high 

humidity), install demist shield to minimize eyepiece 

lens fog prior to execution of mission. 

 

 

Summary of Contents for DTNVS












































Reviews: