background image

Compact FLASH III Digital Audio System 

Copyright©1992-2010 by ACS, Sarasota, Florida 

30 

ALL RIGHTS RESERVED 

 

Diagnostic LED Codes (Red & Green LEDs) 

Green LED 

 

Flashes three times a second while scanning or loading CF Card files. 

 

Steady on when loaded, ready or playing in CFSound mode.

 

 

Flashes once a second while running ACS Basic mode

 

 

Toggles three times a second alternating with the Red LED while self-recording.

 

 

Red LED Error Flashes 

The Red LED can indicate up to 4 error conditions by flashing 1 to 4 unique numeric code patterns from the 
following table in a continuously repeating sequence. The Red LED flashes at two and a half times a second 
for the value of the pattern, followed by a six tenths of a second gap, then the next pattern.  

When self-recording the Red LED alternates with the Green LED three times a second while the recording is 
armed, and is Steady On while recording. 

Flash 

Count 

Error Condition 

CFSound 

Stops 

Problem w/ATA interface, non-compatible CF card, bad CF card, execution stops. 

• 

Error opening .WAV file for that input, incorrect filename, file does not exist. 

 

Error when reading file, file corrupted, unsupported file type, the sound doesn‟t start 
or stops playing. 

 

No valid “*.WAV” files of a CFSound Mode Filename Format found on the CF 
Card – starting ACS Basic. This code will continue until a Basic RUN command is 
issued.

 

 

No valid FAT or FAT32 file system found on the CF Card, execution stops.

 

 

Error seeking within file when starting or resuming sound, the sound doesn‟t start or 
resume.

 

 

Error initializing CODEC, execution stops. 

 

Invalid .WAV file internal structure, file is ignored. 

 

Unsupported .WAV format (not Windows PCM), file is ignored. 

 

10 

Unsupported .WAV sample rate (not 44.1KHz), file is ignored. 

 

11 

Unsupported .WAV sample size (not 16-bit), file is ignored. 

 

12 

Contact closure without matching sound file, a contact closure with matching sound 
file stops this code from flashing. 

 

13 

Speaker is muted by RS-232 command or ACS Basic command. 

 

14 

Problem with CFSOUND.INI file entries. 

 

15 

CFSOUND.INI [DMX] section with no DMX I/O module detected. 

 

16 

CFSOUND.INI [Video] section with no Video Generator module detected. 

 

17 

Unsupported [Video] DisplayMode specified 

 

18 

Error displaying image file on Video Generator 

 

19 

Error writing file when self-recording 

 

20 

Error closing file when self-recording 

 

21 

Error renaming .TMP file at end of self-recording 

 

 
 

Summary of Contents for CFSound-III




























































Reviews: