manualshive.com logo in svg

Acrosser Technology AR-B2104, Manual, Page: 6 / 18

Share
Download
Acrosser Technology AR-B2104 Manual Download Page 6

A C R O S S E R
T E C H N O L O G Y

6

CHAPTER 2 INSTALLATlON

Before using your AR-B2104, you must set the base address of

the I/O port. This chapter provides information on how to set the

base address switch. Pin assignments of the I/O connector is

also provided. Figure 1-2 shows the switch and component lo-

cations of the AR-B2104 card.

2.1 BASE ADDRESS SETTING

There is one DIP switch (SW1) located on the AR-B2104 card. It

is used to select the base port address of the AR-B2104. The

operation of AR-B2104 is controlled through the output ports.

Three consecutive I/O ports are used by the AR-B2104. The

base address of these output ports are selected by using base

address switch SW1. The AR-B2104 is factory-configured for a

base address of 3E0 Hex. lf this base address is already occu-

pied, you will need to change the base address switch setting. lt

is essential that each peripheral device, such as an AR-B2104,

be assigned a unique base address within the range of 100 to

3FC Hex. and that the address is on a 4-byte boundary. Use

Table 2-1 (next page) as a guide to select an unoccupied ad-

dress.

Summary of Contents for AR-B2104



















Reviews:

No comments