Acromag APCe7010E-LF User Manual Download Page 4

AcroPack Series APCe7010E-LF 

PCI Express Carrier Board 

- 4 - 

1.

 

GENERAL INFORMATION 

Intended Audience 

This users’ manual was written for technically qualified personnel who will be 
working with I/O devices using the AcroPack module.  

Preface 

The information contained in this manual is subject to change without notice, 
and Acromag, Inc. (Acromag) does not guarantee its accuracy. Acromag 
makes no warranty of any kind with regard to this material, including, but not 
limited to, the implied warranties of merchantability and fitness for a 
particular purpose. Further, Acromag assumes no responsibility for any errors 
that may appear in this manual and makes no commitment to update, or keep 
current, the information contained in this manual. No part of this manual may 
be copied or reproduced in any form, without the prior written consent of 
Acromag. 

Trademark, Trade Name and Copyright Information 

© 2016 by Acromag Incorporated. 

All rights reserved. Acromag and Xembedded are registered trademarks of 
Acromag Incorporated. All other trademarks, registered trademarks, trade 
names, and service marks are the property of their respective owners. 

Radio Frequency Interference Statement 

This is a Class A product. In a domestic environment this product may cause 
radio interference, in which case the user may find it necessary to take 
adequate corrective measures. 

Environmental Protection Statement 

This product has been manufactured to satisfy environmental protection 
requirements where possible. Many components used (structural parts, 
circuit boards, connectors, etc.) are capable of being recycled. Final 
disposition of this product after its service life must be conducted in 
accordance with applicable country, state, or local laws or regulations. 

APCe7010E-LF Overview 

The APCe7010E-LF is a low-profile Peripheral Component Interconnect 
Express (PCIe) card and is a carrier for a mini-PCIe or AcroPack mezzanine 
module. This carrier board provides a modular approach to system assembly, 
since each carrier can be populated with a choice of analog input/output, 
digital input/output, communication, etc. AcroPack modules.  

Summary of Contents for APCe7010E-LF
























Reviews: