Acromag AcroPack AP441 User Manual Download Page 22

SERIES AP441 ACROPACK  

USER

’S MANUAL 

 

 

 

Acromag, Inc. Tel: 248-295-0310  

            - 20 -                                   

http://www.acromag.com  

- 20 - 

www.acromag.com 

 

Interrupt Pending Port A Status Bit.  This bit can be read to 
determine the interrupt pending status of the AP module.  
When this bit is logic “1” an interrupt is pending and will cause 
an interrupt request if bit-0 of the register is set.  When this 
bit is logic “0” an interrupt is not being requested. 

No Interrupt from Port A 

Interrupt Pending from Port A 

Interrupt Pending Port B Status Bit.  This bit can be read to 
determine the interrupt pending status of the AP module.  
When this bit is logic “1” an interrupt is pending and will cause 
an interrupt request if bit-0 of the register is set.  When this 
bit is logic “0” an interrupt is not being requested. 

No Interrupt from Port B 

Interrupt Pending from Port B 

Interrupt Pending Port C Status Bit.  This bit can be read to 
determine the interrupt pending status of the AP module.  
When this bit is logic “1” an interrupt is pending and will cause 
an interrupt request if bit-0 of the register is set.  When this 
bit is logic “0” an interrupt is not being requested. 

No Interrupt from Port C 

Interrupt Pending from Port C 

Interrupt Pending Port D Status Bit.  This bit can be read to 
determine the interrupt pending status of the AP module.  
When this bit is logic “1” an interrupt is pending and will cause 
an interrupt request if bit-0 of the register is set.  When this 
bit is logic “0” an interrupt is not being requested. 

No Interrupt from Port D 

Interrupt Pending from Port D 

31 to 6  Not Used 

 

 
Module Location In System Register (Read Only)  

(BAR0 + 0x0000 0004)   

This read only register is used identify the module’s plugin location in a 
system.  

Table 3.4   Location Register 

 
Note that any registers/bits not 
mentioned will remain at the 
default value logic low. 
 

 

 

Bit(s) 

FUNCTION 

2 to 0 

Module Site Location Bits.  These bits identify the location on 
the carrier of the AP module.   

000 

Carrier Site A 

001 

Carrier Site B 

010 

Carrier Site C 

011 

Carrier Site D 

Summary of Contents for AcroPack AP441














































Reviews: