background image

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

 

 

 

SV16 TEMPERATURE/PRESSURE BALANCING MIXING VALVE

 

NOTES TO THE INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished.

2. Please read this entire booklet before beginning the installation.

3. Check your installation for compliance with plumbing and other applicable codes.

LIMITED WARRANTY

UNITED STATES AND CANADA

Acorn Controls warrants that its products are free from defects in material or workmanship under normal use and 
service for a period of one year from date of shipment. Acorn's liability under this warranty shall be discharged solely 
by replacement of repair of defective material, provided Acorn is notified in writing within one year from date of 
shipment, F.O.B. Industry, California.

This warranty does not cover installation or labor charges and does not apply to materials, which have been 
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the 
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Acorn under this warranty. 
Acorn shall not be liable under any circumstances for incidental, consequential or direct charges caused by defects in 
materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all other warranties expressed 
or implied. Product maintenance instructions are issued with each unit and disregard or non-compliance with these 
instructions will constitute an abnormal use condition and void the warranty.

FOR TECHNICAL ASSISTANCE 

1.800.743.8259

[email protected]

Date: 09/01/16

Manual #7802-116-000

 

Model SV16

Patent Pending

WWW.ACORNENG.COM

 

ACORN ENGINEERING COMPANY

P.O. BOX 3527
CITY OF INDUSTRY, CA 91744

UNITED STATES OF AMERICA

Acorn Controls 

Division of Acorn Engineering Company

®

, A member of Morris Group International

Model SV16-LVR

Patented Tri-Lever
Handle

Federal
Public Law
111-380 
(No Lead)

Summary of Contents for Controls SV16-LVR











Reviews: