background image

 
 

Warning: 

 

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or 

moisture. 

 

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. 

Caution: 

There are no user serviceable parts inside the unit. DO NOT  open the housing or attempt any 

repairs yourself. In the unlikely event your unit may require service, please contact your nearest 

dealer.

 

Installation: 

The unit should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the 

unit is firmly fixed to avoid vibration and slipping while operating. Make sure that the structure 

to which you are attaching the unit is secure and is able to support a weight of 10 times of the 

fixtures weight. Also always use a safety cable that can hold 12 times of the weight of the unit 

when installing the fixture.   

The equipment must be installed by professionals. It must be fixed in a place where is out of the 

reach of people and no one can pass by or under it. 

 

  2. Technical Specifications   

 DMX 512 Channels: 5/6/8 channels 

 Control Mode: DMX512 

 LCD display for easy navigation 

 0%-100% smooth dimming and various strobe speeds 

 Flicker free 

 

 

Power Voltage

:         AC 100~240V, 50/60Hz 

 

Power Consumption:    

285W 

 

Light Source:

          7pcs RGBW LED 

 

Beam Angle:

           

5°~50°

 

 

3A 

Summary of Contents for MP-350Z

















Reviews: