background image

 
 

 

9B 

press the 

ENTER

 button to setup, to go back to the functions without any change press the

 MENU

 

button again. Hold and press the 

MENU

 button about one second or wait for one minute to exit 

the menu mode. 

Black Out   

To select the 

Black Out

, press the

 ENTER 

button to show the 

BLACK OUT

 on the display. Use the

 

DOWN

 and 

UP

 button to select the 

Yes

 (blackout) or 

No

 (normal) mode. Once the mode has been 

selected, press the 

ENTER

 button to setup, to go back to the functions without any change press 

the

  MENU

  button  again.  Hold  and  press  the 

MENU

  button  about  one  second  or  wait  for  one 

minute to exit the menu mode. 

Sound State 

To select the 

Sound State

, press the 

ENTER

 button to show the 

SOUND STATE

 on the display. Use 

the

 DOWN

 and 

UP

 button to select the 

On

 (Sound Mode On) or 

Off

 (Sound Mode Off). Once the 

mode has been selected, press the 

ENTER

 button to setup, to go back to the functions without any 

change press the

 MENU

 button again. Hold and press the 

MENU

 button about one second or wait 

for one minute to exit the menu mode. 

Sound Sense 

To select the 

Sound Sense

, press the

 ENTER

 button to show the 

SOUND SENSE 

on the display. Use 

the

 DOWN

 and 

UP

 button to adjust the sound sensitivity from 

0

 to 

100

, press the 

ENTER

 button to 

setup,  to  go  back  to  the  functions  without  any  change  press  the

  MENU

  button  again.  Hold  and 

press the 

MENU

 button about one second or wait for one minute to exit the menu mode. 

Pan Inverse 

To select the 

Pan Inverse

, press the 

ENTER

 button to show the 

PAN INVERSE

 on the display. Use 

the

 DOWN

 and 

UP

 button to select the

 Yes

 (pan inversion) or 

No

 (normal) mode. Once the mode 

has  been  selected,  press  the 

ENTER

  button  to  setup,  to  go  back  to  the  functions  without  any 

change press the

 MENU

 button again. Hold and press the 

MENU

 button about one second or wait 

for one minute to exit the menu mode. 

Summary of Contents for LED BEAM 350

























Reviews: