background image

 
 

 

Replace fuse only with the same type. 

 

In the event of serious operating problem, stop using the unit immediately. 

 

The housing, the lenses must be replaced if they are visibly damaged. 

 

DO NOT open the unit as there are no user serviceable parts inside. Never try to repair the unit 

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please 

contact the nearest authorized technical assistance center.   

 

Disconnect the mains power if the fixture is not used for a long time. 

 

DO use original packing materials once transport it again. 

 
 
 
 
 

 

Installation:   

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is 

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to 

which you are attaching the unit is secure and is able to support a weight of 10 times of the 

unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit 

when installing the fixture in the air.   

 

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the 

touch of people and has no one pass by or under it. 

 

If using a 230V 50Hz power supply, DO NOT connect in series more than 18 units; use 
another main supply for the next 18 fixtures. 
If using a 120V 60Hz power supply, DO NOT connect in series more than 9 units; use 
another main supply for the next 9 fixtures. 

 

 

3E 

 

Summary of Contents for Building wash





















Reviews: