background image

 

Hyperlan-Pack 

Quick installation guide 

 

High throughput, outdoor, point-to-point 

Ethernet bridge 

 

 
 
 
 
 

 

Ethernet networks bridging between buildings 

 

Up to 40 Mbps TCP throughput across 5 km 

 

Secure connection, tight radio beam 

 

10/100 Base Tx network interface 

 

IP66 housing, powered from the Ethernet (POE) 

 
 
 
 
 

 
 

Please check the product kit parts against the following list: 

2 x identical Hyperlan-Pack modules 

1 x this documentation, printed 

2 x M12 to RJ45, male, POE, Ethernet cat. 5 cable, 25 m long 

2 x directional antennas, 28 dBi (/L version) 

4 x waterproof plastic caps for M12 connectors 

2 x lightning arrestors 

2 x male-to-male N-type coaxial extenders, 60 cm long 

2 x 50 ohms N-type terminator caps 

1 x CD ROM with drivers and documentations for all ACKSYS 
products 

 
and contact immediately your dealer if any item listed above is missing or 
damaged. 
 
A detailed reference manual about the software complement this quick 
installation guide. 
 
Before continuing, check for the latest documentation on the 

www.acksys.fr

 

web site and read if necessary the software user’s manuals.

 

 
 
 

 

 

 

10, rue des Entrepreneurs  

 Z.A Val Joyeux 

78450 VILLEPREUX - France 

Phone: 

         +33 (0)1 30 56 46 46 

Fax: 

         +33 (0)1 30 56 12 95 

Web: 

         

www.acksys.fr

  

Hotline:  

[email protected]

Sales:  

[email protected]

Documentation ref. DTUS063 rev A0 12/09/09 

-

1

 

Summary of Contents for DTUS063

















Reviews: