aci ACCESS series Installation Instructions And Owner'S Manual Download

Page: 2 / 12

INSTALLATION INSTRUCTIONS:

Note: Side rails and bows are silver finish.

PREPARATION

NOTE ON BED LINERS: With an under-the-rail drop-in bed liner, installation is

possible with minimal trim/cutting of bed liner at front corner of box and back by

tailgate to allow side rail to install properly. Considerable trim/cutting is required

with an over-the-rail drop-in bed liner.

Unpack cover components.

Clean truck box if dirty.

COMPONENTS:

1 driver side rail

1 passenger side rail

6 clamps

1 left and 1 right tension adjuster with nuts & bolts

1 pre-rolled up cover assembly

TOOLS NEEDED:

2 - 1/2” wrenches

1 - Tape measure or ruler

1 - Spring clamp

optional

Protective eyewear

(to hold rails in place while clamping)

Tension adjuster

Front bar

Storage straps

Support bows

Slide lock on

rear bar

Rear bar

Right side rail

Left side rail

Trigger latch

Rail clamps

PARTS DIAGRAM

Summary of Contents for ACCESS series













Search results

Summary of Contents for ACCESS series

Reviews:

Related manuals for ACCESS series

Brands by name

Popular brands

aci ACCESS series, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for ACCESS series

Reviews:

Related manuals for ACCESS series

Brands by name

Popular brands