ACI Laser DFL Ventus Marker Operating Instructions Manual Download Page 46 | Manualshive

Page: 46 / 74

background image

Installation

46

External emission light

Pin 22

EMISSION

24 V, max. 200 mA, fused by poly fuse.

Pin 22 carries 24 V when the shutter is open.
The connected emission warning light signals danger from laser radiation.

Laser ready

Pin 3

READY

24 V, max. 200 mA, fused by poly fuse.

This output produces a summation signal of all possible error states. The output is set
when all components function within normal parameters and the laser is ready for opera-
tion.
This signal can be processed both optically and electronically. This output is an essential
aid, particularly for use in production lines.

Inputs and outputs

Pin 5 to 12

IN1 to IN8

24 V, 3.5 mA

Control inputs for PLC connector

Pin 23 to 30

OUT1 to OUT8

24 V, max. 0.5 A

WARNING

DANGER OF INJURIES AND/OR RISK OF PROPERTY DAMAGE FROM
LASER RADIATION!
Wiring this output is specified for operation in accordance with a class
4 laser.

!

«
...
44
45
46
47
48
...
»

Summary of Contents for DFL Ventus Marker











































































Reviews:

No comments

Related manuals for DFL Ventus Marker

Mentor Visual iQ

Brand: GE Pages: 2

Brand: Camille Bauer Pages: 11

Brand: Camille Bauer Pages: 83

Brand: HANYOUNGNUX Pages: 4

Brand: janitza Pages: 12

Brand: Sabre Pages: 13

Brand: aci Pages: 5

Brand: PASCO Pages: 4

Brand: Kawai Pages: 72

NOVAplus biogas

Brand: mru Pages: 78

Brand: GAGEMAKER Pages: 36

LaserRange-Master i5

Brand: LaserLine Pages: 68

Brand: az-instrument Pages: 12

Brand: INTERSPIRO Pages: 76

Brand: Net2Edge Pages: 37

Brand: Eplus Pages: 17

Brand: Akai Pages: 12

Brand: Eddyfi Technologies Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands