Mode
Clock, RPM, Wheel, Unit, Divider, Thermometer, fuel meter and ODO SETUP
1. Setup operations include, 12/24 hour clock, shift warning RPM, numbers
of engine rotation per signal, wheel circumference, Speed input divider,
units, units of temperature, temperature warning, fuel meter input
resistance selection and odometer adjustment. These must be set up
step by step. The computer will be automatically revert to normal mode
if no button is pressed for 75 seconds at any setting screen
2. Press both MODE & RESET buttons to go into setting mode. In setting
mode, each press of the RESET button increments the flashing digit by
1 or converts units. Press MODE button to confirm the digit setting and
jump to next digit or next setting screen to be set. Press MODE button
for 2 seconds at any setting screen to finish the setting and go to normal
mode.
3. It displays "12 or 24H and XX:XX " symbols as well AM/PM in case you
select 12H. Operates buttons as descriptions of item 2 to finish clock
setting and jump to shift RPM warning setting.
4. It displays the default "RPM r06500", the digit “0” flash. Follow the item
2 of button operation to finish the shift RPM warning setting and jump to
engine specification setting.
5. It displays "RPM SPC-X.X", the default value is 1.0; there are 4 options:
1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal.
For example the value 2.0 means the engine rotate 2 turns to output a
signal. Follow the item 2 of button operation to finish the engine
specifications setting and jump to wheel circumference setting screen.
6. Press RESET button to move in loop sequence from one to another
value of the 4 values. Press MODE button to confirm the setting and
go to wheel circumference setting screen.
7. In "cXXXX" display, "c" means "Circumference", following 4 default
digits; flashing digit is digit to be set. Follow the item 2 of button
operation to finish the wheel circumference setting and jump to signal
divider setting.
8. It displays "P-001" for signals to be divided. Follow item 2 of button
operation to finish the setting and jump to unit setting.
9. It displays KM/H or MPH, each press of RESET button converts unit;
press MODE button to confirm unit setting and jump to thermometer
unit setting.
10. It displays " ˚C ,˚F or oFF", each press of RESET button converts ˚C, ˚F or
Off, the temperature bars will disappear when you select oFF mode;
press MODE button to confirm temperature setting and jump to
temperature warning setting.
11. It displays “100r” and fuel tank symbol, follow the item 2 to select 100,
250, 510ohm, oFF, -100, -250 or -510Ohm and jump to sensor type of
LAP timer setting. The fuel meter bar will disappear if you select oFF
mode
12. It displays Ir, EF1, EF2 or EF3, for configuring the lap time recording,
choose “Ir” if you have an IR sensor or are manually incrementing lap
times with the lap button. Choose EF1/EF2/EF3 if using the
electromagnetic field sensor. In the case where there is one transmitter
on the circuit,choose EF1, if there are 2 transmitters choose EF2 and EF3
where there are 3 transmitters. Follow the item 2 to set sensor type of
LAP timer and jump to odometer setting.
13. It displays “ ODO & 00000X km ”, the “ X ” is from odometer testing in
factory, follow item 2 to setting a desired odometer and jump to clock
setting or return to Normal Mode. This setting screen will disappear
when the odometer is over 30km (18.6Miles) or your setting is over
30km.
Mode
Mode
Mode 2 sec
Mode
Mode
RESET
+
MODE
2 Sec
RESET
+
MODE
2 Sec
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
WHEEL CIRCUMFERENCE TABLE
Tire Size
Tire Size
Tire Size
23 inch
24 inch
25 inch
26 inch
19 inch
20 inch
21 inch
22 inch
15 inch
16 inch
17 inch
18 inch
1835
1915
1995
2075
1516
1596
1676
1756
1197
1277
1357
1436
1. The details below have been calculated using following formula:
Tire Diameter (inches) x 25.4(mm/inches) x 3.1416
= wheel circumference (in mm).
2. Identify the tire size of your ATV/Motorcycle when you need
to change different tire size and key in the corresponding
number shown in the following chart.
3. These values are approximate and will differ for different brands of tyre,
we would always recommend that you measure the distance travelled
per revolution of the wheel in mm and enter this into the computer.
4. The computer calculates the wheel rotating length between 2 passes
of the magnet; use this table to find the settings when you are using
a reed sensor or an universal hall sensor with magnet to measure your
speed.
5. If you are using a cable drive speed sensor then divide the number in
the above table by the number of turns of the cable drive for each
revolution of the wheel. For example if 1 wheel revolution equals 5
turns of speed cable then the wheel circumference has to be divided 5.
Change display of TEMP 1 & 2:
1. Press and hold MODE button for 2 seconds converts TEMP 1 or 2.
2. The screen will change to TEMP 1 automatically in case engine
temperature is higher than the preset warning temperature.
Shift Warning RPM Operation
1. Press MODE button to the RPM screen; pull on the throttle until the
desired shift warning RPM.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer and warning LED will flash to warning you
shift gear.
4. Press RESET button for 2 seconds at the RPM screen to re-adjust the
shift warning RPM
Remote Control Switch for LAP timer:
1. The remote control switch has 2 buttons: MODE and LAP. The MODE
button has the same function as on the main unit.
2. Press and hold the LAP button for 2 seconds to go into the LAP mode.
3. LAP Record operations:
In LAP mode, press LAP button to start the LAP recording function,
each press of MODE button records a set of data LAP & AVG and
displays LAP timer for 3 seconds then changes display to speed
mode automatically, press LAP button to convert stop or start LAP
record function, press and hold the LAP button for 2 seconds to go
out LAP mode and return to normal mode.
Lap
Mode
LAP review operations:
1. In the LAP mode, press MODE button to review the 1st storage data,
it displays number of lap and lap timer.
2. Press the RESET button to switch between lap timer or average
speed of the same LAP; each press of the MODE button displays
data for the next lap.
3. Press and hold LAP buttons for 2 seconds to go out LAP mode and
return to normal mode.
Mode
Lap
2 Sec.
Normal Mode
LAP
2 Sec
Lap Mode
Lap Review Mode
RESET Button
1. Press MODE button to the desired screen then press RESET button
for 2 seconds to reset TRIP 2, MAX SPD/MAX TEMP 1/ MAX RPM
data from stored values to zero individually.
2. The data of Trip 1, AVG & RT will all be reset at the same time when
one of the 3 data functions is being reset.
3. ODO, clock and TT data cannot be reset.
RESET
2 Sec
Backlight Color Adjust:
1. Press MODE button to get to the VOLT screen when not moving;
push and hold RESET button for 2 seconds to go into backlight
color setting mode.
2. It displays “LED and -7-7-7”, the 3 numbers indicate each color of
Red, Green or Blue color to be adjustable, each color has 8 levels
0, 1, 2,..7 for setting, “0” means the color is off, “7” means the color
is turned on 100%.
3. Each press of the RESET button increments the flashing digit by 1,
press MODE button to confirm the flashing digit setting and jump
to next digit to be set. Press MODE button for 2 seconds to finish
the setting and go to normal mode.
RESET
2 Sec
Mode
Mode
Mode
Red Color Setup
Green Color Setup
Blue Color Setup
Normal Mode
LAP
2 Sec
Lap
Lap Mode
Start Record
Mode
Mode
Mode
Lap
2 Sec.
6. You can use more magnets, but the wheel circumference setting must
be divided by the number of magnet you installed.
7. The computer has a built-in software divider setting from 1 to 199 pulses
for different speed signal application, refer to the divider setup, one means
one wheel revolution creates one signal. You have to input the number of
signal per wheel revolution to get a correct speed. We suggest to set divider
at 1 and adjust wheel circumference for normal ACE-S type reed sensor or 2
wires hall sensors, and set the P for gear sensor which has more signals for
one wheel revolution.
Circumferen ce
number
(mm)
Circumferen ce
number
(mm)
Circumferen ce
number
(mm)
Reset
Mode
Lap
2 Sec.
DIGITAL GEAR INDICATOR INSTALL & SETUP
1.set Number of gears(Defaul=6)
2.LCD show 4~8 and Flashing
3.Press RESET key to change the
number of gears
1.Press MODE key to next setting mode
2.LCD show 1 and Flashing
3.Select you motorcycle to 1st Gear
1.Run the Engine at between 2000~4000 RPM
2.fix the speed & rpm about 5 seconds until the
-flashing
1.LCD show 2 and Flashing
2.Select you motorcycle to 2st Gear
3.Run the Engine at between 2000~4000 RPM
4.fix the speed & rpm about 5 seconds until the
-flashing
Press Mode key to return Normal Mode
