Acer Veriton 5200 Service Manual Download Page 58

Page: 58 / 116

Chapter 2

Advanced Options

NOTE:

The Advanced Options menu is available only when you press

in the main menu.

The “Advanced Options” menu allows you to configure the system memory and PCI device settings.

The following screen shows the Advanced Options parameter:

CAUTION:

Do not change any settings in the Advanced Options menu if you are not a qualified technician to

avoid damaging the system.

Product Information

Selecting “Product Information” from the Advanced Options menu displays the following secreen:

This menu lets you configure the system memory.

The following table describes the parameters found in this sub-menu

Parameter

Description

System BIOS ID

R01-C0. BIOS real version

BIOS release date

Summary of Contents for Veriton 5200





















































































































Search results

Summary of Contents for Veriton 5200

Reviews:

Related manuals for Veriton 5200

Brands by name

Popular brands

Acer Veriton 5200, Service Manual

Search results

Summary of Contents for Veriton 5200

Reviews:

Related manuals for Veriton 5200

Brands by name

Popular brands