manualshive.com logo in svg

Acer TravelMate 505, Service Manual, Page: 68 / 104

Share
Download
Acer TravelMate 505 Service Manual Download Page 68

62

Chapter 4

Memory size found by POST differed from CMOS

Run “Load Default Settings” in BIOS Setup Utility.

DIMM

System board

Diskette drive A error

Check that the drive is defined with the proper diskette 
type in BIOS Setup Utility.

Diskette Drive Check. 

Incorrect Drive A type - run SETUP

Check that the drive is defined with the proper diskette 
type in BIOS Setup Utility

Diskette Drive Check. 

System cache error - Cache disabled

CPU board

System board

CPU ID

CPU board

System board

DMA Test Failed

DIMM

CPU board

System board

Software NMI Failed

DIMM

CPU board

System board

Fail-Safe Timer NMI Failed

DIMM

CPU board

System board

Device Address Conflict

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Allocation Error for device

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Failing Bits: nnnn

DIMM

BIOS ROM

System board

Fixed Disk n

None

Invalid System Configuration Data

BIOS ROM

System board

I/O device IRQ conflict

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Operating system not found

Enter Setup and see if fixed disk and drive A are 
properly identified.

Diskette drive

Hard disk drive

System board

Error Messages List

Error Messages

Action in Sequence

505-1.book  Page 62  Thursday, November 4, 1999  4:36 PM

Summary of Contents for TravelMate 505









































































































Reviews:

No comments