manualshive.com logo in svg

Acer TravelMate 2100, Service Manual, Page: 25 / 127

Share
Download
Acer TravelMate 2100 Service Manual Download Page 25

20

Chapter 1

Supported protocols

ACPI 1.0b, SMBIOS 2.3, PCI 2.2, Boot Block, PXE 2.0, Mobile PC2001, 
Hard Disk Password, INT 13h Extensions, PCI Bus Power Management 
interface Specification, EI Torito-Bootable CD-ROM Format Specification 
V1.0, Simple Boot Flag 1.0

BIOS password control

Set by switch, see SW5 settings on Chapter 5.

Second Level Cache

Item

Specification

Cache controller

Built-in CPU

Cache size

128KB for Cerelon

®

 CPU; 512KB for Intel

®

 Northwood CPU, Mobile 

Pentium

®

 4 CPU and Cerelon

® 

Prescott CPU; 1MB for Intel

®

 Prescott CPU

128KB for Cerelon

®

 CPU used in TM2000 series

512KB for Intel

®

 Northwood, Mobile Pentium

®

 4 and Cerelon

®

 Prescott CPU 

used in TM2500 series and TM2000 series

1MB for Intel

®

 Prescott CPU used in TM2500 series

1st level cache control

Always Enabled

2nd level cache control

Always Enabled

Cache scheme control

Fixed-in write back

System Memory

Item

Specification

Memory controller

ATI RC300M

Onboard memory size

0MB 

DIMM socket number

2 Sockets

Supports memory size per socket

128MB

Supports maximum memory size

2048MB

Supports DIMM type

DDR-DRAM

Supports DIMM Speed

333 MHz

Supports DIMM voltage

2.5 V

Supports DIMM package

200-pin so-DIMM

Memory module combinations

You can install memory modules in any combinations as long as they 
match the above specifications.

Memory Combinations

Slot 1

Slot 2

Total Memory

0MB

128MB

128 MB

128MB

0MB

128 MB

128MB

128MB

256 MB

256MB

0MB

256MB

0MB

256MB

256MB

256MB

128MB

384MB

128MB

256MB

384MB

256MB

256MB

512MB

0MB

512MB

512MB

BIOS

Item

Specification

Summary of Contents for TravelMate 2100
































































































































Reviews:

No comments