background image

TABLE  OF  CONTENTS

Special notes on LCD monitors .................................................. 1
Information for your safety and

 

comfort .................................. 2

Unpacking ................................................................................... 5
Attaching/Removing the base .................................................... 6
Screen position adjustment ........................................................ 6
Connecting the power cord ....................................................... 7
Safety  precaution ....................................................................... 7
Cleaning your monitor ............................................................... 7
Power saving ............................................................................... 8
DDC .............................................................................................. 8
Connector Pin Assignment ......................................................... 9
Standard Timing Table..................................................................11
Installation.....................................................................................12
User controls..................................................................................13
How to adjust a setting................................................................14

Troubleshooting............................................................................19

Summary of Contents for P203



























Reviews: