background image

v

English

people will walk on the cord.

•   

 If an extension cord is used with this product, make sure that the total ampere rating 

of the equipment plugged into the extension cord does not exceed the extension 
cord ampere rating. Also, make sure that the total rating of all products plugged into 
the wall outlet does not exceed the fuse rating.

•    Do not overloa

d a power outlet, strip or receptacle by plugging in too many devices. 

The overall system load must not exceed 80% of the branch circuit rating. If power 
strips are used, the load should not exceed 80% of the power strip’s input 

rating.

•    This pro

duct

’s power cord is equipped with a three-wire grounded plug. The 

plug only fits in a grounded po

wer outlet. Make sure the power outlet is properly 

grounded before inserting the power cord plug. Do not insert the plug into a non-
grounded power outlet. Contact your electrician for details.

•    Use the

 product only with the supplied power supply cord set. If you need to 

replace the power cord set, make sure that the new power cord meets the following 
requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V 
minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.

Product servicing

Do not attempt to service this product yourself, as opening or removing covers may 
expose you to dangerous voltage points or other risks. Refer all servicing to qualified 
service personnel.

Unplug this product from the wall outlet and refer servicing to qualified service 
personnel when:

•    the power cord or plug is damaged, cut or frayed

•    liquid was spilled into the product

•    the product was exposed to rain or water

•    the product has been dropped or the case has been damaged

•    the product exhibits a distinct change in performance, indicating a need for service

•    the product does not operate normally after following the operating instructions

Note: 

The grounding pin also provides good protection from 

unexpected noise produced by other nearby electrical devices that 
may interfere with the performance of this product.

Warning! The grounding pin is a safety feature. Using a power 

outlet that is not properly grounded may result in electric 

shock and/or injury.

Summary of Contents for HA220QABI































Reviews: