manualshive.com logo in svg

Acer Aspire 5739 Series, Service Manual

Share
Download
Acer Aspire 5739 Series Service Manual Download Page 13

Chapter 1

3

•

USB 2.0 ports•HDMI™ port with HDCP support

•

HDMI™ port with HDCP support

•

External display (VGA) port

•

Consumer infrared (CIR) port

•

RF-in jack*

•

eSATA port

•

Headphones/speaker/line-out jack with S/PDIF support

•

Microphone-in jack

•

Line-in jack

•

Ethernet (RJ-45) port

•

Modem (RJ-11) port

•

DC-in jack for AC adapter

Environment

•

Temperature:

•

Operating: 5 °C to 35 °C

•

Non-operating: -20 °C to 65 °C

•

Humidity (non-condensing):

•

Operating: 20% to 80%

•

Non-operating: 20% to 80%

NOTE: 

Items marked with * denote only selected models. 

NOTE: 

The specifications listed above are for reference only. The exact configuration of your PC depends on 

the model purchased.

Summary of Contents for Aspire 5739 Series







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands