background image

 

ACE095 

Page 5 of 17  

Rev Date: 12.7.2021

 

 

 

Chapter 1 - Illustrated System Disassembly Instructions 

 

Chapter 8 is intended to provide guidance to recyclers on the presence of materials and components at 

the product/family level, per Article 15 of the EU WEEE Directive 2012/19/EU. The provided information 

should also help direct recyclers to proper methods for removing parts and general product disassembly 

instructions. This Chapter also outlines specific substances, mixtures, and components that must be 

removed from any separately collected electronic waste component and shall be disposed or recovered 

in compliance with EU Directive 2008/98/EC.  

Please note: All the illustrations in the below disassembly instructions are for demonstration only. The 

system and components shown in this section are a representative sample.   

CAUTION:

 Always power off the system and unplug the power cord(s) first before disassembling the 

system! 

 

Representative Desktop Component Layout   

 

 

Power Supply 

Removeable 
Hard drives 

Motherboard 

Heat Sink 
Fan 

Optical Drive 

Memory 
(2X) 

Processor 

Case Fan 

Summary of Contents for Vision Series


















Reviews: