*
If you constantely keep pushing
the power button, you can see
the number of all tests conduct-
ed with the device (starting with
zero after a calibration) and also
the last measurement result.
IMPORTANT NOTICE: WHEN
YOU HAVE EATEN, DRUNKEN
ALCOHOL OR SMOKED A
CIGARETTE, WAIT AT LEAST 15
MINUTES BEFORE STARTING
THE MEASUREMENT. ANY TEST
CONDUCTED PRIOR TO THE EXPI-
RATION OF THE RECOMMENDED
WAITING PERIOD WILL RESULT
IN INACCURATE RESULTS.IF THE
TEST RESULT IS BELOW 0.005%
BAC THEN THE DEVICE SHOWS
0.000% BAC ON THE DISPLAY.
THIS HAPPENS BECAUSE AT
A LOW RANGE OF ALCOHOL
CONCENTRATION IT IS POSSIBLE
TO MEASURE OTHER MATERIALS
IN YOUR MOUTH.
Only the usage of original
ACE mouthpieces ...
Guarantees test result accuracy
Guarantees 100% hygenity
Guarantees full warranty of this
device
ACE INSTRUMENTS ADVISES:
EVEN IF YOU GET A RESULT
MEANING „SAFE RANGE“, YOU
SHOULD NEVER DRIVE AFTER
CONSUMING ALCOHOL OR DO
ANY OTHER ACTIVITIES THAT
ARE SEVERELY IMPAIRED BY
ALCOHOL CONSUMPTION AND
MIGHT ENDANGER YOUR HEALTH
AND SAFETY OR THE HEALTH
AND SAFETY OF OTHERS.
ONLY USE THE PROVIDED
SINGLE PACKED AND
HYGIENIC MOUTHPIECES -
MORE ARE AVAILABLE AT
WWW.ACE-INSTRUMENTS.NET.
DURING EACH TEST THE
BREATHALYZER´S INTERNAL
AND EXTERNAL PARTS COME
INTO CONTACT WITH HUMAN
SECRETION (SALIVA, BLOOD,
SWEAT, ETC.)!
USE SAFTEY GLOVES WHEN
PULLING OUT A MOUTHPIECE
USED BY ANOTHER PERSON!
YOU CAN BUY APPROPRIATE
GLOVES E.G. AT ACE TECHNIK
(WWW.ACE-TECHNIK.DE).
Conducting the measurement:
1. Press the power button to turn
on the device
*
.
2. The device warms up, a count-
down starts, wait until you can
see “0” on the display, then you
can start the test which can be
done in three different ways:
a) picture 2. a) - by means of
using a mouthpiece (best
accuracy)
b) picture 2. b) - by means of
using a straw (good accuracy)
c) picture 2. c) - (passive mode)
just blow your breath upon
the sensor opening (sufficient
accuracy)
3. Blow steadily for 4 seconds
until a double beep tone
concludes.
4. If the breath sample is insuffi-
cient the ACE Easy shows “Flo”.
Turn off the device and repeat
the test. Please blow steadily
and without a break into the
mouthpiece (like you would
whistle).
5. After a sufficient breath sample
you will see the digit “0” moving
left to right in the display as
the device analyzes the breath
sample. After a few seconds the
display shows the alcohol level
in the format #.##% BAC (% BAC
= default setting). In the USA
the legal limit for drivers over
21 years is 0.08% BAC, below 21
years it is 0.00% BAC (status:
Oct. 2016).
6. When showing the test result
the display will blink ca. 10
times. Then you hear a beep
tone with each further blink and
after five blinks the device turns
off.
7. For turning off manually keep
the power button pressed. The
display shows “Out” (off). After
a few seconds the ACE Easy
turns off.
2. a)
2. b)
2. b)
2. c)
FLO
The breath sample was interrupted or not strong enough for a
measurement. After the sensor warmed up itself automatically,
please blow steadily and without a break into the mouthpiece (like
you would whistle).
BAT
The battery power is low. Please replace the 2 batteries inside the
device with 2 new ones (type AA, 1.5V, LR6, Alkaline batteries). If
you change depleted batteries against new ones please mind their
polarity (+/- pole). Do not use rechargeable batteries!
CAL
If you test over 1.000 tests, ACE Easy will display “CAL” sign for
3 seconds when warming up for test. This “CAL” sign informs about
the appropriate time for calibration. To maintain the measurement
accuracy of this breathalyzer it should be calibrated.
For a calibration service you can send the device to ACE Instruments
(see www.ace-instruments.net).
SEN
The sensor is defective, please contact ACE:
[email protected], www.ace-instruments.net
Notice: The exchange of the sensor is excluded from warranty and
liable to costs.
OUT
The device turns off (either by pressing the power button constantely
for 4 seconds or 10 seconds after displaying the test result).
Display indications: