background image

                                                                                

 

Never perform maintenance procedures while this generator is running. Allow this generator to cool before commencing any maintenance 
procedures. Keep heat, sparks and flame away.
 
 

                                                                                

 

Improper maintenance and/or failure to correct any problems prior to operating this generator can cause a malfunction which could cause 

death or serious injury. Always follow the inspection and maintenance recommendations and schedules in this manual. 
 

Recommended Maintenance Schedule 

 

 

 

Each Use 

Every Month or 
Each 20 Hrs 

Every 3 Months or 
Each 50 Hrs 

Every 6 Months or 
Each 100 Hrs 

Every Year or 
Each 300 Hrs 

Engine Oil 

Check Level 

 

 

 

 

 Replace  

 

 

 

Air Filter 

Check 

 

 

 

 

 Clean     

 

 

Fuel Filler Cap 

Clean 

 

 

 

 

Spark Plug 

Check/Clean 

 

 

 

 

Fuel Tank 

Verify Gas Level 

 

 

 

 

 Clean      

  

Figure 10 - Recommended maintenance schedule 

 
 

Cleaning the Generator 

 
Always try to use this generator in a cool dry place. If this generator becomes dirty, the exterior can be cleaned with a damp cloth, soft brush, 

vacuum and/or pressurized air. 

 

Never clean this generator with a bucket of water and/or a hose as water can get inside and cause a short circuit or corrosion. 
 

Never use gasoline to clean parts of this generator. 

 

 

Checking the Oil Level 

 

Even though this generator is equipped with an automatic shutoff to protect it from damage due to low oil, it is important to check the oil level in the 
engine crankcase before each use to ensure that there is a sufficient quantity. 

 

To check the oil level: 
1. Verify that this generator is shut down and on a level surface. 

2. Unscrew the oil filler/dipstick cap from the engine as illustrated in Figure 11. 

3. With a dry cloth, wipe the oil off of the dipstick that is located on the inside of the cap. 

4. Insert the dipstick as if replacing the cap and then remove again. There should be oil on the dipstick. If there is no oil on the dipstick, or oil is 

visible only at the very end of the dipstick, add oil until the engine crankcase is filled (see “Changing/Adding Oil” in this section of this manual). 

5. Confirm that the oil filler/dipstick cap is properly in place when finished verifying the oil level. 
 

 

Model AC-G0004 5500 Surge Watts / 5000 Running Watts Electric Start Portable Generator 

20

 

Summary of Contents for AC-G0004





































Reviews: