background image

EXI-310 INVERTED MICROSCOPE SERIES 

ACCU-SCOPE

®

 

18

TROUBLESHOOTING 

Under certain conditions, performance of this unit may be adversely affected by factors other than defects. If a 
problem occurs, please review the following list and take remedial action as needed. If you cannot solve the 
problem after checking the entire list, please contact your local dealer for assistance. 

OPTICAL

 

PROBLEM 

CAUSE 

SOLUTION 

The illumination is on, but the 
field of view is dark. 

The socket pin is not connected to the 
illumination column 

Connect it securely 

The bulb is burnt out. 

Replace it with a new one 

The brightness is set too low 

Set it to the appropriate position 

Two many filters are stacked 

Reduce them to the minimum required 
number 

The edge of the field of view is 
obscured or not evenly 
illuminated. 

The nosepiece is not in the located position 

Turn the nosepiece into the position where 
you can hear it engaged 

the color filter is not inserted fully 

Push it in all the way 

The phase contrast slider is not located in the 
proper position 

Move the slider until it clicks into place  

Dirt or dust is visible in the field 
of view 

Dirt/dust on the specimen 

Replace with a clean specimen 

Dirt/dust on the eyepiece 

Clean the eyepieces 

The image glares 

The iris diaphragm is closed too much 

Open up the iris diaphragm 

Visibility is poor 

Image is not sharp

Contrast is poor

Details are indistinct

Phase contrast effect
cannot be obtained

The objective is not correctly engaged in the 
light path 

Turn the nosepiece into the engaged position 

the aperture diaphragm is opened or stopped 
down   too far in brightfield observation  

adjust the aperture diaphragm properly 

The lens (condenser, objective, ocular or  
culture dish) become dirty  

Clean it thoroughly 

In the phase contrast observation, the bottom 
thickness of the culture dish is more than 
1.2mm. 

 Use a the culture dish whose bottom 
thickness is less than 1.2mm 

Use a brightfield objective  

Change to the phase contrast objective 

The light annulus of the condenser does not 
match the phase annulus of the objective. 

Adjust the light annulus so that it matches the 
phase annulus of the objectives 

The light annulus and the phase annulus are 
not centered 

Adjust the centering screws to center it 

The objective used is not   compatible with 
phase contrast observation 

Please use the compatible objective 

When looking at the edge of the culture dish, 
the phase contrast ring and the light ring is 
deviated from each other 

Moving the culture dish until you obtain the 
phase contrast effect. You also could 
demount the slider, and set the field 
diaphragm lever to “

” 

One side of the image is 
blurred 

The objective is not in the center of the light 
path 

Insure the nosepiece is in the “clicked” 
position 

The specimen is not correctly mounted on the 
stage. 

 Place the specimen on the stage correctly. 

The optical performance of the culture vessel 
bottom plate is poor (profile irregularity, etc.) 

Use a vessel with a good profile irregularity 
characteristic. 

Summary of Contents for EXI-310-PH






















Reviews: