background image

 

EXC-400 MICROSCOPE SERIES  

 

 

 

 

ACCU-SCOPE

®

     

                   

73 Mall Drive, Commack, NY  11725  •  631-864-1000  •  www.accu-scope.com 

10

 

DETAILED ASSEMBLY 

(continued) 

 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Installing the Stage - 

(Fig. 6 & 7)

 

Lower the condenser to its lowest position by turning the 
condenser carrier knob counterclockwise 

①.

 

 

Remove protective tape and bag from stage and 
specimen holder 

.  (The stage comes with the 

specimen holder pre-mounted to the top of the stage).   

 

Loosen the thumb screw 

 on the front of the stage. 

 
Position the X-Y movement knobs 

 to the right and 

align the circular mount on the bottom of the stage with 
the circular bracket 

 on the condenser/stage carrier 

and set the stage in place so that it is centered over the 
condenser below.  
 
Tighten the thumb screw 

 on the front of the stage. 

 
Raise the condenser carrier by turning the knob 
clockwise. 
 
Figure 7 shows the stage in place. 

 

 
 
 

Installing the Viewing Head - 

(Fig. 8)

 

Using the 5mm Hex wrench, loosen the lock screw 

①.

 

 
Position the viewing head 

② 

above the dovetail opening 

③ 

as shown and with it tilted slightly down on the right, 

slide the dovetail under the notches in the dovetail hole 
and set it into place with the two eyepiece tubes 

④ 

facing forward.  
 
Retighten the lock screw 

①.

 

 
 

 

 

 

 

 

Fig. 6 

Fig. 7 

 

 

 

 

 

 

 

 

 

Fig. 8 

 

Summary of Contents for EXC-400 Series

























Reviews: