background image

A111 Pulsed Coherent Radar (PCR) 
Datasheet, v1.8 

© 2019 Copyright by Acconeer 

2019-06-12 

Page 34 of 34

 

Disclaimer 

The information herein 

is believed to be correct as of the date issued. Acconeer AB (“

Acconeer

”) will 

not be responsible for damages of any nature resulting from the use or reliance upon the information 
contained herein. Acconeer makes no warranties, expressed or implied, of merchantability or fitness 
for a particular purpose or course of performance or usage of trade. Therefore, it is the user’s 
responsibility to thoroughly test the product in their particular application to determine its performance, 
efficacy and safety. Users should obtain the latest relevant information before placing orders.  

Unless Acconeer has explicitly designated an individual Acconeer product as meeting the requirement 
of a particular industry standard, Acconeer is not responsible for any failure to meet such industry 
standard requirements. 

Unless explicitly stated herein this document Acconeer has not performed any regulatory conformity 
test. It is the user’s responsibility to assure that necessary regulatory conditions are met and approvals 
have been obtained when using the product. Regardless of whether the product has passed any 
conformity test, this document does not constitute any regulatory approval of the user’s product or 
application using Acconeer’s product.  

Nothing contained herein is to be considered as permission or a recommendation to infringe any 
patent or any other intellectual property right. No license, express or implied, to any intellectual 
property right is granted by Acconeer herein. 

Acconeer reserves the right to at any time correct, change, amend, enhance, modify, and improve this 
document and/or Acconeer products without notice.

  

This document supersedes and replaces all information supplied prior to the publication hereof. 

© 2018 by Acconeer 

– All rights reserved 

 

Acconeer AB 

 

www.acconeer.com 

IDEON Gateway 

[email protected] 

Scheelevägen 27 

+46 10 218 92 00 

223 63 LUND 
Sweden

 

Summary of Contents for A111



































Reviews: