74
RU
StreamPunch
TM
Ultra/Ultra MP
Предупреждающие надписи
ВЫБОР СЪЕМНОГО СИЛОВОГО КАБЕЛЯ
(СЛЕДУЮЩЕЕ
ЗАМЕЧАНИЕ
ОТНОСИТСЯ
ТОЛЬКО
К
МОДЕЛЯМ,РАССЧИТАННЫМ НА СЕТЬ С НАПРЯЖЕНИЕМ 230 В
И ЧАСТОТОЙ 50 Гц; ТАКИЕ МОДЕЛИ ПОСТАВЛЯЮТСЯ В
ЕВРОПЕЙСКИЙ СОЮЗ)
ВНИМАНИЕ: ПРИ ВЫБОРЕ СЪЕМНОГО СИЛОВОГО
КАБЕЛЯ ДЛЯ АППАРАТА STREAMPUNCH ULTRA
ВСЕГДА
СОБЛЮДАЙТЕ
СЛЕДУЮЩИЕ
М
ЕРЫ
ПРЕДОСТОРОЖНОСТИ.
Съемный силовой кабель состоит из трех частей: вилка, шнур и
разъем Каждая из этих частей должна соответствовать
европейским нормативам по безопасности.
В целях безопасности съемный силовой кабель должен отвечать
следующими минимальным требованиям.
НЕ ИСПОЛЬЗУЙТЕ СИЛОВОЙ КАБЕЛЬ, НЕ ОТВЕЧАЮЩИЙ
СЛЕДУЮЩИМ МИНИМАЛЬНЫМ ТРЕБОВАНИЯМ
.
ВИЛКА:
3 А, 250 В, 50/60 Гц, соответствие европейским
нормативам для проводников классов 1, 3.
ШНУР:
Тип H05VV-F3G0.75, Harmonized (< HAR >). Символы “< >”
указывают на то, что шнур отвечает соответствующему
европейском стандарту (ПРИМЕЧАНИЕ: Вместо “HAR” может быть
другой приемочный знак европейского агентства по безопасности,
проверившего шнур. Например, может стоять “< VDE >”).
РАЗЪЕМ:
3 А, 250 В, 50/60 Гц, соответствие европейскому
стандарту IEC 320. Длина кабеля не должна превышать 3 м.
Можно
использовать
кабель,
все
части
которого
превосходятуказанные выше требования
.
Обслуживание, StreamPunch Ultra
Не пытайтесь самостоятель но обслуживать аппарат StreamPunch
Ultra
. Для проведения ремонта или обслуживания аппарата
StreamPunch Ultra
обратитесь в авторизованный сервисный центр.
НЕ СНИМАЙТЕ КРЫШКУ АППАРАТА.
Внутри аппарата НЕТ частей, обслуживаемых пользователем. Не
открывайте крышку аппарата во избежание возможных травм и/или
ущерба для собственности или повреждения самого аппарата.
Обслуживание, Штампы
Каждый штамп тщательно смазан маслом на фабрике перед
поставкой аппарата. В ходе обычной эксплуатации это масло
расходуется, так что штамп нуждается в повторной смазке. В ходе
регулярного техобслуживания необходимо производить смазку
каждого комплекта матриц.
Инструкции по обслуживанию комплектов матриц приведены в
Разделе 8 Руководства по комплектам матриц перфоратора
StreamPunch Ultra.
2. ВВЕДЕНИЕ
Благодарим за приобретение аппарата StreamPunch Ultra. Этот
универсальный аппарат позволяет выполнять перфорацию для
самых разных стилей переплета путем простой смены штампа.
Аппарат прост в эксплуатации.
StreamPunch Ultra
– инновационное решение для перфорации со
следующими характеристиками:
Быстрая
смена
самозащелкивающихся
штампов
без
инструментов или рычажков.
На всех штампах StreamPunch Ultra стоит идентификационная
метка со схемой расположения отверстий и названием
переплета.
Удобное место хранения для двух дополнительных
комплектов матриц.
Режим работы и позиционирование продукта
Перфоратор GBC StreamPunch Ultra представляет собой гибкое и
недорогое решение при перфорировании в условиях малых и
средних тиражей. Устройство предназначено для использования в
типографиях, где как правило производится перфорирование 20-
30% документов от общего объема печатной продукции. При
проведении
перфорирования
длительного
цикла,
продолжительность которого превышает 4 часа, рабочие качества
могут отличаться или ухудшаться по причине широкого спектра
плотности печатных материалов и возможных внешних условий.
Среднемесячный объем печати
-
номинальный объем 600 000
листов (A4/letter), с допущением, что весь объем распределятся в
пропорции 50/50 (300 000 листов – перфорация, и 300 000 листов
– в обход).
Максимальный рекомендуемый ежемесячный объем -
максимальный рекомендуемый ежемесячный объем перфорации
не должен превышать 400 000 листов.
Максимальная нагрузка -
в дополнение к вышеупомянутым
условиям, следует перфорировать не более 2 листов плотностью
300
г/м
2
на 5 листов плотностью 75 г/м
2
.
Бумага наибольшей
плотности как правило используется только на передней и задней
сторонах обложки переплета.
Рабочие поставки штампов
Штампы считаются расходными материалами, и в случае износа
подлежат замене, так как их заточка невозможна.
На каждый штамп предоставляется 90-дневная гарантия с даты
покупки. Гарантия недействительна при использовании штампа
вне указанных характеристик.
Ресурс штампа будет максимальным, если его смазывать через
каждые 100 000 рабочих циклов (подробности см. в Руководства
по эксплуатации штампов)
Расчетный ресурс штампов составляет 750 000 операций при
использовании бумаги плотностью 75 г/м
2
.
Это - минимальный
ожидаемый ресурс. Срок службы штампа НЕ гарантируется из-за
широкого диапазона плотности бумаги и окружающих условий.
Если Вы собираетесь использовать штамп в режимах, которые
превышают его ресурс, настоятельно рекомендуется иметь
достаточное количество соответствующих штампов под рукой,
чтобы минимизировать время простоя.