Access Garden Products Eltham-D Assembly Instructions Manual Download Page 16 | Manualshive

Page: 16 / 17

Access Garden Products Eltham-D Assembly Instructions Manual Download Page 16

P14

TROUBLESHOOTING

TROUBLESHOOTING

P15

CORNER TRIMS WILL NOT FIT

The most common cause of this problem is the end glass protruding over the front leg. This is
normally caused because the frame work is not square against the wall. See page 7.

GLASS STICKS TOGETHER

This is normally due to the handles not being put on the right side of the glass. See page 12 for
details of where the handles should be fitted to the glass.

If the glass has stuck together, push the two sheets to the back of the channel, then slowly pull
the front sheet of glass forward from one end. This will release the suction between the sheets.

HANDLES COME OFF

As the handles are of a clamp design they can be pulled off if too much force is applied to them.
If the glass has stuck together due to moisture, or if the glass does not slide smoothly, this will
strain the clip part of the handle and cause it to come off.

Ensure that the channels and the glass are kept clean at all times to minimise the sliding force
needed. Candle wax applied to the channel and the underside of the glass will also help the
sliding action. Also check that the handles have been fitted correctly. See page 12 for full
instructions.

Handles can be rejuvenated by placing them in hot water, cleaning them carefully, then
squeezing the clip together while the plastic is still warm. Leave to cool before fitting.

If handles come off frequently either purchase some new handles from Access or use a glue
such as 'liquid nails' or 'no more nails' to permanently glue the handles to the glass.

SHELVES WILL NOT FIT INTO THE BACK LEGS

Check that the back legs have been fitted the right way round - see page 2.
Check that dimension A = B - see page 7.

LOUVRE VENT DOES NOT FULLY CLOSE ON COLD
DAYS

Loosen the two screws which hold the automatic opener to the vent. Push the opener up as far
as it will go. Retighten the 2 screws.

If the unit still does not fully close, lubricate the opener mechanism and all the pivot points with
WD-40

WATERING INLET LEAKS

Try tightening the inlet fitting as it needs to be tight to seal.

«
...
14
15
16
17
»

Summary of Contents for Eltham-D


















Reviews:

No comments