background image

 

Page 2 of 40

 

 

 

Dear Valued Customer,

 

 

Congratulations on your Academy play set purchase! Please read and completely understand the contents of this 

owner’s manual. This manual contains specific instructions and warnings that must be followed to prevent injuries.

 

This play set is for residential use only. This play set is NOT intended for public or commercial use. The warranty 

will be voided if the play set is used in a commercial application.

 

The product is designed for children between the ages of 3-8. Children must NOT play on this set until it is properly 

assembled  and  inspected  by  an  adult.  Adult  supervision  is  required  at  all  times  while  children  are  playing  on  the 

equipment. Do not allow children under six (6) years old to be near during the assembly of this product due to choking 

hazards of small parts.

 

The equipment must be installed on level ground. Uneven ground must be leveled prior to installation. Installation 

on sloping or uneven ground will put stress on the joints, causing the unit to become loose and unstable which may result 

in serious injuries. You must ensure there are no obstructions or structures (e.g. electrical wires, branches, house, fence, 

garage, etc) within six (6) feet from the equipment.

 

The 

Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommend to install and 

maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded rubber (for equipment up to 8 

feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock absorbing material. Dirt and grass, 

which  are  the  most  prevalent  surfaces  under  home  playground  equipment,  do  not  adequately  protect  children  from 

serious head injuries. Install protective surfacing at least six feet in all directions from play equipment.  For swings, the 

surface should extend, in back and front, twice the height of the suspending bar.  Do not install your play set over hard 

surface, e.g. asphalt, concrete, packed earth, tile or brick floor. Please refer to extracts from the CONSUMER PRODUCT 

SAFETY COMMISSIO

N’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK contained in this manual for further 

details.

 

Do not allow children to use the product during windy or wet weather conditions. It is highly recommended the product 

be anchored into the ground to prevent movement and to make the swing set more stable during use. You should consult 

a local contractor about ways to anchor the product in your location.

 

The  equipment must be checked before each use  and maintained regularly.  This  includes, but is  not limited  to 

inspecting  the  play  set  for  cracks,  excess  wear,  missing  parts,  loose  connections  and  for  overall  integrity.  When  the 

equipment shows any signs of weakness or damage, you must stop using the play set immediately, properly store the 

set or restrict access by users until the condition is resolved.

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for MSC-5576













































Reviews: