ABSCO SHEDS REGENT 30292RK Assembly Instructions Manual Download | Manualshive

Page: 21 / 26

background image

Absco Industries

Assembly Instruction Manual

ABSCO REGENT SHED

MODEL: 30292RK

3.00mW x 2.96mD x 2.10mH

Model: 30292RK

20/09/18

1.1

21

FINAL CONSTRUCTION

Each anchor consists of one nut, bolt, M10
dynabolt and steel angle.
Drill a 10mm hole into the wall sheet.
Drill a 10mm hole into the concrete.

Bolt and Nut*
M10 4.6/S

Steel Angle*
35 x 35 x 3

M10 Dynabolt*

* Denotes hot dip galvanised fi nish

Wall Sheet

Slab

14A

Bend the top and bottom
flanges as shown, then hook the
bottom flanges under the top
channel and screw top to the
ridge beam with two screws.

ANCHORING OF

SHED

Location of 14

concrete anchors

250

250

250

250

1000

1000

700

700

640

640

640

640

640

640

640

640

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

«
...
19
20
21
22
23
...
»

Summary of Contents for REGENT 30292RK



























Reviews:

No comments

Related manuals for REGENT 30292RK

Brand: Kiehn-Holz Pages: 20

Brand: Solid Pages: 32

Brand: Solid Pages: 32

Brand: Palmako Pages: 55

Palmako EL 16-2755

Brand: Lemeks Pages: 44

Palmako EL18-4533

Brand: Lemeks Pages: 53

Brand: Lemeks Pages: 79

Brand: Lemeks Pages: 159

Brand: Universo Consumer Products Pages: 20

Brand: Palmako Pages: 54

Brand: GARDIVAL Pages: 29

Brand: Palmako Pages: 75

FLORENCE 41218MR-GP-12

Brand: Gazebo penguin Pages: 54

Brand: OLT Pages: 45

winchester arbour

Brand: Rowlinson Garden Products Pages: 2

266H Wheel Horse 72052

Brand: Toro Pages: 40

Brand: Toro Pages: 40

265H Wheel Horse

Brand: Toro Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands