Outputs:
Pigtronix Power is equipped to meet the DC requirements of the
most demanding pedal board setups, with 8 individually isolated outputs.
A pair of 9V @ 100mA outlets are intended for standard guitar pedals
such as BOSS which do not have high current draw.
Four, independently switchable (9V, 12V, 15V, 18V) multi-voltage outlets
provide the flexibility to run virtually any DC powered stomp box. Two of
these individually isolated, switchable outlets are rated at 100mA while
the other two can provide up to 300mA of current from each output.
A pair of 18V @ 300mA outlets are specifically intended for digital
Pigtronix pedals such as the Infinity Looper and Echolution 2 which have
high current draw (and require individually isolated power), or for use
with the included daisy chain connectors to power up to five analog
Pigtronix pedals from one outlet.
Polarity: The cables provided with the Pigtronix Power support the industry
standard positive (+) barrel and negative (-) center polarity.
Features:
• 2x 9V outlets @ 100mA
• 2x variable (9V/12V/15V/18V) @ 100mA
• 2x high current variable (9V/12V/15V/18V) @ 300mA
• 2x high current 18V @ 300mA
• Switchable for 115V or 230V wall voltage
• Short Circuit Protection
• Courtesy AC outlet
Included Accessories:
• 5pcs of 2.1mm connector 12” cable
• 5pcs of 2.1mm connector 24” cable
• 2pcs of Daisy chain w/ 5x 2.1mm connector
• 1pcs IEC wall plug
Wall Voltage:
Pigtronix Power IEC power input is switchable between
115V and 230V for use anywhere in the world. Make sure the input
voltage switch is set to the appropriate voltage for your country.
Combining Outputs:
Any output may be combined with any other output
when stacked in series. If combining outputs in parallel, only outputs of
the same voltage may be used together.
Dimensions:
8 5/8” x 3 ¼” x 1 5/8”
Weight:
2lb, 7.3oz
WARNING:
Some pedals may be damaged if powered using a voltage
that exceeds the level required by the manufacturer, e.g. powering a
9V pedal with 12V, 15V or 18V. Pigtronix assumes no responsibility or
liability for equipment damage caused by misuse of this power supply.
WARNING:
READ THIS FIRST BEFORE OPERATING! IMPORTANT SAFETY
INSTRUCTIONS (1) Read these instructions. (2) Keep these instructions.
(3) Heed all warnings. (4) Follow all instructions. (5) Do not use this
apparatus near water. (6) Clean only with dry cloth. (7) Do not block any
ventilation openings. Install in accordance with manufacturer’s instructions.
(8) Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including amplifiers) that produce heat. (9)
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet. (10) Protect the power cord from being walked
on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus. (11) Only use attachments,
accessories, and hardware specified by the manufacturer. (12) Unplug
the unit during lightning storms or when unused for long periods of time.
(13) Refer all servicing to qualified service personnel. Servicing is required
when the unit has been damaged in any way, such as power supply cord
or plug is damaged, liquid has been spilled, the unit has been exposed
to rain or moisture, does not operate normally, or has been dropped.
(14) When mounting the unit, ensure that the area around the AC IN is
unobstructed so that the power cord can be easily removed.
www.pigtronix.com
www.pigtronix.com
