background image

Part number 20219, Rev 0 
 

 

Programming Mode 

Note: The programming mode gives access to several functions that are 
not  intended  for  user  adjustment.  The  procedures  below  provide 
direction to the functions that you can adjust. Please do not attempt to 
change any of the other functions in the programming area or your unit 
may be damaged or become unstable.    

 
Locking and Unlocking the Control 

The control keys can be locked out to prevent inadvertent operation.  

To  lock  the  control  keys,  simultaneously  press  and  hold  the  up  arrow  and  the  down 
arrow. The display will show “POF”.  At this point you can only use keys to view the SET 
temp and the minimum and maximum stored temperatures.  
 
To unlock the control keys, simultaneously press and hold the up arrow and the down 
arrow.  The  display  will  show  “Pon”.  The  control  keys  are  now  unlocked  and  you  can 
perform the programming functions below.  

 
Adjusting the temperature control set points: 

NOTE:  The  temperature  control  set  points  are  preset  at  the  factory  to 
provide the desired air and product temperatures inside of the unit and 
require  no  further  adjustment.  Please  contact  the  manufacturer’s 
Technical  Service  Department  before  making  any  adjustments  to 
determine  if  adjustment  is  necessary  and,  if  so,  to  make  sure  it  is 
performed properly. 

 

 

 

-

 

To set the compressor off set point, press and hold the SET key for 2 seconds. The current 
value will be displayed and the C or F icon will flash. Use the up or down keys to change the 
value. Press SET again to lock in the value.

 

-

 

To  set  the  compressor on  set  point,  you  will  need  to  adjust  the differential,  or  Hysteresis 
setting. This is the number of degrees the controller will allow temperature to drift up until 
it  restarts  the  compressor.  For  example,  if  the  SET  point  is  3  degrees  Celsius  and  the 

Summary of Contents for ABT-HC-UCBI-0420-ADA

















Reviews: