background image

 

 Part number 20079, Rev 0 

17 

 

MAINTENANCE AND CLEANING 

Manual-Defrost Freezers (All models except ABT-3020AP) should be defrosted whenever ¼ to ½ 
inch of frost has accumulated. Use the procedures in the defrosting section starting at the 
bottom of this page for best results. They should also be cleaned periodically. Use the cleaning 
agents and suggestions in the table below for best results.  

Model ABT-3020AP is an Auto-Defrost Freezer and requires little maintenance. Like the other 
models, it should be cleaned periodically to keep it running efficiently. Use the cleaning agents 
and suggestions in this table for best results.  

CLEANING

 

PART 

CLEANING AGENTS 

TIPS AND PRECAUTIONS 

Interior and Door 

Liners 

Soap and water 

Baking soda and water 

Use 2 tablespoons of baking soda in 1 quart of 

warm water 

Be sure to wring excess water out of sponge or 

cloth before cleaning around controls, light bulb 

or any electrical parts. 

Door Gaskets 

Soap and water 

Wipe gaskets and their seating surfaces with a 

clean soft cloth 

Shelves 

Soap and water 

Do not wash removable shelves in dishwasher 

Exterior and 

Handles 

Soap and water 

Non Abrasive Glass 

Cleaner 

Do not use commercial household cleaners, 

ammonia, or alcohol to clean handles 

Use a soft cloth to clean smooth handles 

Do not use a dry cloth to clean smooth handles 

 

 

Manual Defrosting - 

All models except ABT-3020AP

 

 

It is important to defrost and clean the freezer when ¼ to ½ inch of frost has accumulated. Frost 

may tend to accumulate faster on upper part of the freezer due to warm, moist air entering the 

freezer when the door is opened. Between defrost evolutions; you can minimize frost build-up 

by using a plastic scraper to remove frost. Scrape with a pulling motion. Never use a metal 

Summary of Contents for ABT-2020MP





















Reviews: