background image

7

AUTO

OPEN

MAN

Abloy

®

 DA430 is an electromechanical swing door operator for moderate use. 

It can be used on single, internal doors. The Abloy

®

 DA430 has a ”Push&Go” 

function. When Push&Go is in operation and door is pushed or pulled manually, 
operator opens the door to adjusted opening angle and closes the door after a 5 
second of hold open time. 

Internal monitoring

Obstructed opening: 

The door is set free for 5 seconds and the impulse is restrained during that time. 

After that, the operator tries to open the door.  If the door is still obstructed in the 

same position after 4 trials, operator closes the door.

   

   

 

Obstructed closing:

The door is set free for. After that, new trial is done to close the door. Maximum 

amount for trials is 4. If it is exeeded, the door is set free for 1 minute. Atfter this 

new trial is done to close the door.

4 OPERATION

5 MODE 

SWITCH

Note! There is 3 seconds constant delay 

when mode switch is changed position 

OPEN to AUTO or MANUAL.

The door opens via an impulse and closes after 

the adjusted hold open time.

Manual use.

The door opens and stays open.

Summary of Contents for DA430





























Reviews: