background image

|     Error resolution and maintenance  

58

Proceed as follows to trigger the reset pushbutton on the Wallbox eM4 Twin:

Unlock both the side RCCB flaps using the key sup-
plied and flip them up to unlock the housing cover.

Open the housing cover to the front.

Locate the reset pushbutton, which is set back on the 
main module of the wallbox.

 

• The access is marked on the sticker of the commu-

nication module with a screwdriver and the word 

 

Reset

.

Reset

Insert an insulated screwdriver and press the reset 
pushbutton for the desired duration.

 

< 3 seconds: 

Reset

 

< 10 seconds:

 Restore to factory settings

The wallbox restarts after a short moment and 
changes to the corresponding operating mode after 
the boot phase:

 

< 3 seconds: 

Ready for charging

 

< 10 seconds:

 Ready for reconfiguration 

Measures for handling errors and warnings

Malfunctions may occur during configuration and operation of the Wallbox eM4 Twin. While certain malfunctions 
have no effect on the charging operation, other errors can lead to a reduction in the charging current or prevent the 
charging operation.
For the Wallbox eM4 Twin, malfunctions are documented as follows:

Description

Visualisation example

Description

HMI of the wallbox in the 
event of malfunction

In the event of a malfunction, the status indicator of 
the faulty charge point pulsates red.
(Illustration: Right-hand charge point)

Wallbox energy meter

In the event of a malfunction or warning, the identifi-
cation code is displayed cyclically in the second line 
of the energy meter window for the affected charge 
point.

Summary of Contents for eM4 Twin







































































Reviews: