background image

BIOS Setup 

3-23 

3.4.  PC Health Menu 

 

CPU Shutdown Temperature: 

Once the system or CPU temperature exceeds the temperature specified, the CPU will 
shutdown automatically to avoid damaging. This function only works for an ACPI OS 
such as Windows 98/ Windows 2000 with ACPI activated. The options are Disabled, 
70

°

C/158

°

F, 75

°

C/167

°

F, 80

°

C/176

°

F, and 85

°

C/185

°

F. The default setting is 

85

°

C/185

°

F

NOTE:

 This item is enabled only for 604-pin CPU. For 603-pin CPU, the CPU will 

be auto detected and this item will be disappeared. 

CPU Warning Temperature 

This item lets you select the temperature at which you want the system to send out a 
warning message to the PC speakers of when the temperature goes beyond either limit. 
You can select the temperatures you want. The options are Disabled, 50

°

C/122

°

F, 

53

°

C/127

°

F, 56

°

C/133

°

F, 60

°

C/140

°

F, 63

°

C/145

°

F, 66

°

C/151

°

F, and 70

°

C/158

°

F. 

The default setting is 

70

°

C/158

°

F

 

NOTE:

 This item is enabled only for 604-pin CPU. For 603-pin CPU, the CPU will 

be auto detected and this item will be disappeared. 

User’s Manual 

Summary of Contents for WI-2P







































































Reviews: