manualshive.com logo in svg

Abit Hot Rod 100 Pro, User Manual

Share
Download
Abit Hot Rod 100 Pro User Manual Download Page 15

BIOS Setting Utility

3-1

User’s Manual

Chapter 3.

 

BIOS Setting Utility

In this chapter we will discuss the BIOS setting procedure of this IDE RAID controller card
before starting the software installation.

3-1.

 

Set Motherboard CMOS Setup

No changes are necessary in the motherboard CMOS setup for resources or drive types. As
this IDE RAID controller card is a PCI Plug and Play device, the motherboard’s PCI PnP
BIOS automatically assigns the Interrupt and Port address. For this IDE RAID controller
card to be the bootable IDE controller, confirm in the motherboard’s Standard CMOS Setup
that the drive types (for hard disk drives) are set for “Not Installed” or “None”. Or use the
“Boot to SCSI” option, if this setting is available in the motherboard’s BIOS. No changes
are needed for CD-ROM drives that are attached to the motherboard IDE controller.

3-2.

 

Enter the BIOS Setting Menu

After you have installed this IDE RAID controller card and attached the hard disks, reboot
your system. Press <

CTRL

> and <

H

> key while booting up the system to enter the BIOS

setting menu. The main menu of BIOS Setting Utility appears as shown below:

Summary of Contents for Hot Rod 100 Pro























































Reviews:

No comments

Brands by name

Popular brands

Load more brands