manualshive.com logo in svg

Abit Hot Rod 100 Pro, User Manual

Share
Download
Abit Hot Rod 100 Pro User Manual Download Page 11

Hardware Installation

2-1

User’s Manual

Chapter 2.

 

Hardware Installation

This IDE RAID controller card is as easy to install as any other computer peripheral. It uses
the Plug & Play design concept. First, plug this controller card into any PCI slot on your
motherboard. Second, connect the Ultra ATA/100 devices to its IDE connectors using the
included Ultra ATA/66 cables.

2-1.

 

Installing the Hot Rod 100 Pro

Installing this controller card into your computer is a simple process. You just have to insert
the card into any available PCI slot on the motherboard (see figure below).

➠

 

Open your computer case.

➠

 

Remove the inside slot cover of an available PCI slot on the motherboard.

➠

 

Insert this controller card into the open slot.

➠

 

Fasten the controller card bracket to the case.

➠

 

Attach the two-threaded IDE HDD LED connector of the computer case to HDD-LED
connector on this controller card. (Note: Watch out the pin orientation.)

➠

 

Connect the Ultra ATA/100 HDD to the IDE connectors on this controller card.

Figure 2-1: The installation of the Hot Rod 100 Pro controller card

Summary of Contents for Hot Rod 100 Pro























































Reviews:

No comments

Brands by name

Popular brands

Load more brands