manualshive.com logo in svg

Abit BG-72, User Manual, Page: 27 / 56

Share
Download
Abit BG-72 User Manual Download Page 27

BIOS Setup 

3-7 

Head 

This item configures the numbers of read/write heads. 

Precomp 

This item displays the number of cylinders at which to change the write timing. 

Landing Zone 

This item displays the number of cylinders specified as the landing zone for the 
read/write heads. 

Sector 

This item configures the numbers of sectors per track. 

 

 

 

 

Back to Standard CMOS Features Setup Menu

 

# 

Drive A 

This item sets the type of floppy drives (usually only Drive A) installed. 

Floppy 3 Mode Support 

This item allows you to use “3 Mode Floppy Drive” in Japanese computer system by 
selecting drive A, B, or both. Leave this item to its default [Disabled] setting if you 
are not using this Japanese standard floppy drive. 

Video 

This item defines the video mode of the system. This motherboard has a built-in VGA 
graphics system; you must leave this item at the default value. 

Halt On 

This item determines whether the system stops if an error is detected during system 
boot-up.

 

User’s Manual 

Summary of Contents for BG-72

























































Reviews:

No comments