background image

 

ABICOOLER 1300

11 Disassembly

EN 

-

 19

11 Disassembly

12 Disposal

Dispose of BTC coolant

The coolant must not be disposed of with normal household waste. Do not allow the product to enter the 
sewage system. 
► Please take note of the following information in the safety data sheet:
— 14 06 03*: Other solvent and solvent mixtures
— 15 01 10*: Packaging containing residues of or contaminated by dangerous substances.
— 15 01 02: Plastic packaging.
Contaminated packaging: Disposal in accordance with official regulations.

12.1 Disposing of materials

This product is mainly made of metallic materials that can be melted in steel and iron works and are thus 
almost infinitely recyclable. The plastic materials used are labeled in preparation for their sorting and 
separation for later recycling.

WARNING

W

Electric shock

Dangerous voltage due to defective cables.
► Check all live cables and connections for proper installation and damage.
► Replace any damaged, deformed or worn parts.

CAUTION

W

Risk of injury due to unexpected start

If power is supplied during maintenance, cleaning or disassembly, rotating parts can start running 
unexpectedly and lead to injuries from cuts.
► Switch off the device.
► Disconnect all electrical connections.

NOTICE

► Only qualified personnel are permitted to perform work on the device or system.
► Please also consult the operating instructions for the welding components and welding torch.
► Observe the information provided in the following section:

8 Decommissioning on page EN

-

13.

Equipment marked with this symbol is covered by European Directive 2012/19/EU on 
waste electrical and electronic equipment (WEEE).
— Electrical and electronic equipment must not be disposed of with household waste.
— Electrical equipment must be disassembled prior to proper disposal.

11 Disassembly on page EN

-

18

— Components of electrical equipment must be collected separately and recycled in an 

environmentally friendly manner.

► Observe the local regulations, laws, provisions, standards and guidelines.
► Contact your local authority for information about the collection and return of 

electrical and electronic equipment. 

Summary of Contents for ABICOOLER 1300

























Reviews:

Related manuals for ABICOOLER 1300