background image

Please read fully and understand before operating the Infield PRO 

ABI(

Absolute Innovations, Inc.

)

    

-        

www.abiattachments.com

        -       855-211-0598               Page 

5

 of 

8

 

 

8)

 

Once the PRO is attached to a tow vehicle, lower the wheels on the PRO using the square hand 
jack, until all attachments raise fully clear of the shipping pallet. 

9)

 

When all the attachments on the PRO have properly cleared the shipping pallet the PRO can be 
removed from the shipping pallet. 

**Ensure that all bolts are tightened prior to using the PRO. If any bolts are loose, secure them 
properly before use.** 

Infield PRO Standard Operating Procedure –  

Once the PRO is removed from the shipping pallet, it will need to be adjusted for first time 
use. Below are setup instructions for setting up the PRO for use with the profile blades or 
Vibraflex. 

Profile Blades: 

1)

 

To setup the PRO for use with the profile blades take the PRO to an area that has a hard flat 
surface. 

2)

 

 Next, raise the wheels off the ground using the square 
hand jack until the profile blades are resting on the 
ground. Raise the wheel s fully off the ground to allow the 
profile blades to rest firmly on the surface.  

3)

 

Using the top link, increase/decrease the amount of thread 
showing on the top link using the center handle on the top 
link. Continue until the profile blades are sitting level with 
the surface. 

4)

 

The PRO is now ready to be used with the profile blades. 

 
 

Vibraflex: 

 

For assembly of the Vibraflex refer to the Vibraflex setup guide. 

 

1)

 

To setup the PRO for use with the Vibraflex take the PRO to an area with a hard flat surface. 

2)

 

 Next, raise the wheels off the ground using the square 
hand jack until the pins of the Vibraflex are resting 
firmly on the ground.  

3)

 

Using the top link, increase/decrease the amount of 
thread showing on the top link using the center handle 
on the top link. Continue until the Vibraflex is sitting 
level with the surface. 

4)

 

The PRO is now for use with the Vibraflex. 

Figure 3 

Figure 4 

Summary of Contents for Infield Rascal Pro









Reviews: