Visit:
www.abisupport.com
Call Toll Free:
877-788-7253
Email:
34
35
ITEM
PART #
DESCRIPTION
1
10-20209
NYLOCK NUT: 5/8-11: ZINC CL
2
10-20306
HX HD BOLT: 5/8-11 X 4.5": ZINC GR8
3
10-40032
BRKT: WEIGHT AND DRAGMAT: RASCAL
3
2
1
10-90580 KIT: WEIGHT SUPPORT BRACKET
If adding weight to the Rascal Unit is desired to sink deeper
into the material, 10-90580 KIT: WEIGHT SUPPORT BRACKET
is available.
This can be mounted to the Rascal by pulling the pin
(or bolt) out of the upright brackets welded to the tube
weldment that the toplink mounts to above the finish rake.
Slide the weight bracket onto the upright brackets with the
top holes in the weight bracket in line with the top holes in
the upright brackets. The lower holes in the weight bracket
will line up with the lower holes in the upright brackets (
Fig
50A and 50B
). Re-insert the pin thru the weight bracket,
upright brackets and toplink as before. Slide the 5/8-11
Hex bolt supplied with the weight bracket (a 5/8" diameter
pin can be used as well) thru the second hole in the weight
bracket and upright brackets then thread locknut onto bolt
and tighten using 15/16" wrenches or socket set (
Fig 51
).
(2) 40 LB weights (P/N R66949) can be purchased from a
local tractor dealership or online and mounted onto the
optional weight kit (as shown in
Fig 52
).
10-90580 Weight
Bracket Kit.
Upright Brackets that are welded to the
tube weldment above the finish rake.
P/N R66949
weights.
P/N R66949 weight
Fig 52.
Fig 50A.
Fig 50B.
Fig 51.
Fig 53
Fig 54
Fig 55
To install Left (10-90490) and Right (10-90491) Discs:
Number of Disc required:
1.
Grab tongue of unit and flip unit over backward
so it sits on rake with tongue vertically upward
(recommend 2 people to lift). Remove pins and
Profile Blades or Scarifiers (as shown in
Fig 53
).
2.
Slide Left Discs (10-90490) into pockets on left
side of unit and Right Discs (10-90491) into pockets
on right side of unit (see
Fig 54
).
3.
Raise Wheels all the way up during disc
operation. Lower wheels when transporting unit.
NOTE:
Not compatible with Rascal LGR or Infield Rascal
Pro Models.
4.5' Rascal uses (1) Left Disc and (1) Right Disc
(~3.6’ working width)
5.5' Rascal uses (2) Left Discs and (2) Right Discs
(~4.8’ working width)
6.5' Rascal uses (2) Left Discs and (2) Right Discs
(~4.8’ working width)
7.5' Rascal uses (2) Left Discs and (2) Right Discs
(~4.8’ working width)
• Recommend pining hole in disc shank closest
to disc into lowest hole in pocket (farthest
from main frame) (
Fig 54
and
Fig 55
).
• Disc shanks must be slid into every other
pocket with the shanks toward the inside and
the discs facing outwards of the unit so the
discs will push the soil outward (
Fig 54
and
Fig 55
).
Pin disc Shank in lowest pocket hole mounted
so that the disc shank is toward the inside of
the unit and the disc is facing outward.
Left side of unit
Right side of unit
10-90490 KIT: LEFT FOOD PLOT DISC
10-90491 KIT: RIGHT FOOD PLOT DISC
Options (cont'd)