manualshive.com logo in svg

Abell Adrenaline 3D V2, Manual

Share
Download
Abell Adrenaline 3D V2 Manual Download Page 11

Use the cut off flat carbon strips for elevator joiners. Glue one strip on the top and one on the 
bottom. The edge of the carbon fiber strip should be flush with the leading edge of the elevator 
half’s. 

 

 

8)

 

SERVO AND CONTROL HORN INSTALATION.

  Slide the rudder servo into the fuselage 

as shown

. 

Position the rudder servo so that it lays flat against the bottom of the wing and the 

wire lead exits the servo towards the front of the plane on the left side of the fuselage. Now slide 
the elevator servo into the fuselage from the opposite side so that the wire lead exits the servo 
towards the front of the plane on the right side of the fuselage.   Fasten the servos into the 
fuselage with the screws that came with your servos and a plastic blind nut.  (Hint; plastic blind 
nuts can be made from the small servo arm that came with the servo by cutting off the ends and 
drilling the center hole of each end with a 1/16” drill bit, drive each screw through the foam and 
then into the pre drilled 1/16” hole as shown below)                                        

 

 

 

 

 

 

Summary of Contents for Adrenaline 3D V2




















Reviews:

No comments

Brands by name

Popular brands

Load more brands