background image

 

7

19.  Make a test cut with a paper pile using the full cutting height.  If necessary do a final 

adjustment with the cutting depth adjustment screw (#4). 

20.  IMPORTANT – The clamp bar must be adjusted in a way that the cutting edge of the kn ife in 

its home position is covered by the clamp bar. 

 

 

 

 

 
 
 
 
 
Changing of cutting stick 
 

Should the bottom sheet of a paper pile not be cut across its full length, the cutting stick (#2) must 
be turned, rotated or exchanged. 

 

IMPORTANT – If the knife has been lowered by means of the cutting depth adjustment screw 
(#6) to compensate for a worn cutting stick, then this adjustment screw (#6) has to be turned back 
to its highest setting before the cutting stick (#5) is turned, rotated or exchanged.  Then re -adjust 
screw (#6) again to obtain the optimal cutting depth.  A knife that is set too low can inflict damage 
not only to the cutting stick, but also to the knife and the knife drive system.  

 

The cutting stick (#2) is inserted into the machine table and fixed by hooking it into a pin located 
on the left between the knife guide plates. 

 
Lubrication 
 

IMPORTANT – Before removing any machine covers for service or maintenance, always 
disconnect machine from power supply. 

 

From time to time all moving parts have to be oiled or greased.  Before lubricating clean all parts 
and ensure that they are free of paper dust and dirt.  The following parts have to be lubricated: 

Summary of Contents for Ideal Cutter 4810









Reviews: