ABB Zenith MX250 Page 12 Operation And Maintenance Manual Download

Page: 12 / 36

ABB Zenith

ZTSCT / ZBTSCT Operation & Maintenance Manual

Accessory Definitions

Test Switch, Momentary

Test Switch, Maintained Auto/Momentary Test

6AP

Test Switch, Maintained/Momentary utilizing keypad

Test Switch, Maintained - Auto / Momentary - Test,

Key Operated

Test Switch, Maintained - Auto / Maintained - Test,

Key Operated

Auxiliary Contact, operates on Source 1 line failure.

A1E

Auxiliary Contact, operates on Source 2 line failure.

Auxiliary Contact: Closed in emergency (Source 2)

Additional Available (10 max.) and need to be specified.

Auxiliary Contact: Closed in normal (Source 1)

Additional Available (10 max.) and need to be specified.

A62

Sequential Universal Motor Load Disconnect Circuit.

Normally closed auxiliary contacts for motor loads. Open

0-60 seconds prior to transfer, after transfer, or both in

either direction then re-close in timed sequence after transfer.

AB3

Auxiliary Contact: Closed in bypass emergency (Source 2)

(S.P.D.T.) (Standard up to 400 Amp) Additional Available

(10 max.) and need to be specified.

AB4

Auxiliary Contact: Closed in bypass normal (Source 1)

(S.P.D.T.) (Standard up to 400 Amp) Additional Available

(10 max.) and need to be specified.

Battery charger connections.

Calibrate

While monitoring the actual Phase to Phase voltage levels

and Frequency with a calibrated test equipment, the Phase

to Phase voltage sensing and Frequency can be adjusted

accordingly. Calibration capabilities are available for

Frequency and AB, BC, CA Phase to Phase voltage for

both Sources. Adjust via SET menu (see page 18)

CDP

Clock Exerciser Load/ No Load: Allows the Generator

to start and run unloaded or to simulate a power failure,

start Generator and run under load. Can be configured

by end user for 1, 7, 14, 28, 365 day cycle. (See page 16)

CDT

Load or NO-Load. One event exerciser with adjustable

Engine exercise timer. Exercise duration can be set between

5 and 60 minutes in 1 minute increments. Can be config-

ured to run every 1, 7, 14, or 28 days. Factory Default is 20

minutes. When exerciser is impending, (*E*) appears in

the upper right hand corner of LCD screen. See page

14 for instructions. Configured via CFG (see page 17).

Set via SET menu (see page 18).

CTAP

Alarm Panel on transfer to Source 2 with Silence button.

Disconnect Switch, Auto/Inhibit. Inhibits transfer in either

direction when in inhibit. Allows automatic operation when

in Auto. (40-400 Amps optional, 600-4000 Amps standard)

(Delayed Transition Only)

Time Delay from Neutral Switch position to Source 1

position. Adjustable 0-10 minutes in 1 second increments.

Standard setting is 5 seconds Adjust via SET menu (see

page 18)

(Delayed Transition Only)

Time Delay from Neutral Switch position to Source 2

position. Adjustable 0-10 minutes in 1 second increments.

Standard setting is 5 seconds.Adjust via SET menu (see

page 18)

Engine Start Contact

EL/P

Event Log:

Sequentially Numbered Log of 16 events

that track date, time, reason and action taken

System Data: Total Life Transfers (N2P)

Days Powered Up

Total Transfers to S2

Total S1 Failures

Time S1 available in Hrs

Time S2 available in Hrs. (N1P)

Fan contact, operates when generator is running.

Heater and Thermostat

Frequency Meter, Door mount.

K/P

Frequency Indication for S1 and S2

LNP Center-off position LCD-Indicator

Indicating LED lights:

Indicates Switch in Source 2 position.

Indicates Switch in Source 1 position.

Indicates Source 1 available.

Indicates Source 2 available.

Summary of Contents for Zenith MX250





































Search results

Summary of Contents for Zenith MX250

Reviews:

Related manuals for Zenith MX250

Brands by name

Popular brands

ABB Zenith MX250, Operation And Maintenance Manual

Search results

Summary of Contents for Zenith MX250

Reviews:

Related manuals for Zenith MX250

Brands by name

Popular brands