manualshive.com logo in svg

ABB Welcome H8138.T Series, Product Manual

Share
Download
ABB Welcome H8138.T Series Product Manual Download Page 18

Commissioning

Product manual 2TMD041800D0006

│

18

8

Commissioning

8.1

Welcome screen and home screen

This outdoor station will light up and display the welcome screen when someone approaches
the station or if the station screen is touched.

Click the bulletin to display it as full screen.

Click the area (not the bulletin) to access the home screen (see the picture below on the right).

No. 

Function

1

Welcome message

If there is no bulletin, the Welcome screen will display according to the welcome screen time.
(1...60 s)

2

Developer information

Developer information can be text or a picture. It is sent from management software.

3

Bulletin

If there are any bulletins, the screen will be displayed according to the number of bulletins before
accessing the home screen.

■

Bulletin number = 1, the screen will be displayed for 10 s

■

Bulletin number = 2, the screen will be displayed for 20 s

■

Bulletin number = 3, the screen will be displayed for 30 s

Summary of Contents for Welcome H8138.T Series










































Reviews:

No comments

Brands by name

Popular brands

Load more brands