background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 
— 

ABB Limited 
Measurement & Analytics 

Howard Road, St. Neots 
Cambridgeshire, PE19 8EU 
UK 
Tel: 

+44 (0)870 600 6122 

Fax: +44 

(0)1480 

213 

339 

Email: [email protected] 
 

ABB Automation Products GmbH 
Measurement & Analytics 

Schillerstr. 72 
32425 Minden 
Germany 
Tel: +49 

571 

830-0 

Fax: +49 

571 

830-1806 

 

abb.com/temperature 

  

ABB Inc. 
Measurement & Analytics 

125 E. County Line Road 
Warminster, PA 18974 
USA 
Tel: +1 

215 

674 

6000 

Fax: +1 

215 

674 

7183 

 

 

 

 

 

 

SM

/TTX2

00/SIL-E

N R

ev. E

 

07.2

018

 

 

— 

We reserve the right to make technical changes or modify the contents of this document 
without prior notice. With regard to purchase orders, the agreed particulars shall prevail.  
ABB does not accept any responsibility whatsoever for potential errors or possible lack of 
information in this document.  
We reserve all rights in this document and in the subject matter and illustrations contained 
therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole or 
in parts – is forbidden without prior written consent of ABB. 
Copyright© 2018 ABB 

All rights reserved 

3KXT200010R4801 

 

 

Summary of Contents for TTH200





















Reviews: